Admin مدير المنتدى
عدد المساهمات : 18959 التقييم : 35383 تاريخ التسجيل : 01/07/2009 الدولة : مصر العمل : مدير منتدى هندسة الإنتاج والتصميم الميكانيكى
| موضوع: كتيب يحتوي على شرح معظم أكواد برمجة ماكينات التحكم الرقمي - CNC CNC Programming Codes الأربعاء 21 يوليو 2021, 1:28 am | |
|
أخوانى فى الله أحضرت لكم كتيب يحتوي على شرح معظم أكواد برمجة ماكينات التحكم الرقمي CNC CNC Programming Codes Power Automation America The new generation of CNCs - PC Based and Open Architecture
و المحتوى كما يلي :
G-Codes simple definition G00 Rapid traverse G01 Linear interpolation with feedrate G02 Circular interpolation (clockwise) G03 Circular interpolation (counter clockwise) G2/G3 Helical interpolation G04 Dwell time in milliseconds G05 Spline definition G06 Spline interpolation G07 Tangential circular interpolation / Helix interpolation / Polygon interpolation / Feedrate interpolation G08 Ramping function at block transition / Look ahead "off" G09 No ramping function at block transition / Look ahead "on" G10 Stop dynamic block preprocessing G11 Stop interpolation during block preprocessing G12 Circular interpolation (cw) with radius G13 Circular interpolation (ccw) with radius G14 Polar coordinate programming, absolute G15 Polar coordinate programming, relative G16 Definition of the pole point of the polar coordinate system G17 Selection of the X, Y plane G18 Selection of the Z, X plane G19 Selection of the Y, Z plane G20 Selection of a freely definable plane G21 Parallel axes "on" G22 Parallel axes "off" G24 Safe zone programming; lower limit values G25 Safe zone programming; upper limit values G26 Safe zone programming "off" G27 Safe zone programming "on" G33 Thread cutting with constant pitch G34 Thread cutting with dynamic pitch G35 Oscillation configuration G38 Mirror imaging "on" G39 Mirror imaging "off" G40 Path compensations "off" G41 Path compensation left of the work piece contour G42 Path compensation right of the work piece contour G43 Path compensation left of the work piece contour with altered approach G44 Path compensation right of the work piece contour with altered approach G50 Scaling G51 Part rotation; programming in degrees G52 Part rotation; programming in radians G53 Zero offset off G54 Zero offset #1 G55 Zero offset #2 G56 Zero offset #3 G57 Zero offset #4 G58 Zero offset #5 G59 Zero offset #6 G63 Feed / spindle override not activeG66 Feed / spindle override active G70 Inch format active G71 Metric format active G72 Interpolation with precision stop "off" G73 Interpolation with precision stop "on" G74 Move to home position G75 Curvature function activation G76 Curvature acceleration limit G78 Normalcy function "on" (rotational axis orientation) G79 Normalcy function "off" G80 - G89 for milling applications: G80 Canned cycle "off" G81 Drilling to final depth canned cycle G82 Spot facing with dwell time canned cycle G83 Deep hole drilling canned cycle G84 Tapping or Thread cutting with balanced chuck canned cycle G85 Reaming canned cycle G86 Boring canned cycle G87 Reaming with measuring stop canned cycle G88 Boring with spindle stop canned cycle G89 Boring with intermediate stop canned cycle G81 - G88 for cylindrical grinding applications: G81 Reciprocation without plunge G82 Incremental face grinding G83 Incremental plunge grinding G84 Multi-pass face grinding G85 Multi-pass diameter grinding G86 Shoulder grinding G87 Shoulder grinding with face plunge G88 Shoulder grinding with diameter plunge G90 Absolute programming G91 Incremental programming G92 Position preset G93 Constant tool circumference velocity "on" (grinding wheel) G94 Feed in mm / min (or inch / min) G95 Feed per revolution (mm / rev or inch / rev) G96 Constant cutting speed "on" G97 Constant cutting speed "off" G98 Positioning axis signal to PLC G99 Axis offset G100 Polar transformation "off" G101 Polar transformation "on" G102 Cylinder barrel transformation "on"; cartesian coordinate system G103 Cylinder barrel transformation "on," with real-time-radius compensation (RRC) G104 Cylinder barrel transformation with center line migration (CLM) and RRC G105 Polar transformation "on" with polar axis selections G106 Cylinder barrel transformation "on" polar-/cylinder-coordinates G107 Cylinder barrel transformation "on" polar-/cylinder-coordinates with RRC G108 Cylinder barrel transformation polar-/cylinder-coordinates with CLM and RRC G109 Axis transformation programming of the tool depth G110 Power control axis selection/channel 1 G111 Power control pre-selection V1, F1, T1/channel 1 (Voltage, Frequency, Time) G112 Power control pre-selection V2, F2, T2/channel 1 G113 Power control pre-selection V3, F3, T3/channel 1 G114 Power control pre-selection T4/channel 1 G115 Power control pre-selection T5/channel 1 G116 Power control pre-selection T6/pulsing output G117 Power control pre-selection T7/pulsing output G120 Axis transformation; orientation changing of the linear interpolation rotary axis G121 Axis transformation; orientation change in a plane G125 Electronic gear box; plain teeth G126 Electronic gear box; helical gearing, axial G127 Electronic gear box; helical gearing, tangential G128 Electronic gear box; helical gearing, diagonal G130 Axis transformation; programming of the type of the orientation change G131 Axis transformation; programming of the type of the orientation change G132 Axis transformation; programming of the type of the orientation change G133 Zero lag thread cutting "on" G134 Zero lag thread cutting "off" G140 Axis transformation; orientation designation work piece fixed coordinatesG141 Axis transformation; orientation designation active coordinates G160 ART activation G161 ART learning function for velocity factors "on" G162 ART learning function deactivation G163 ART learning function for acceleration factors G164 ART learning function for acceleration changing G165 Command filter "on" G166 Command filter "off" G170 Digital measuring signals; block transfer with hard stop G171 Digital measuring signals; block transfer without hard stop G172 Digital measuring signals; block transfer with smooth stop G175 SERCOS-identification number "write" G176 SERCOS-identification number "read" G180 Axis transformation "off" G181 Axis transformation "on" with not rotated coordinate system G182 Axis transformation "on" with rotated / displaced coordinate system G183 Axis transformation; definition of the coordinate system G184 Axis transformation; programming tool dimensions G186 Look ahead; corner acceleration; circle tolerance G188 Activation of the positioning axes G190 Diameter programming deactivation G191 Diameter programming "on" and display of the contact point G192 Diameter programming; only display contact point diameter G193 Diameter programming; only display contact point actual axes center point G200 Corner smoothing "off" G201 Corner smoothing "on" with defined radius G202 Corner smoothing "on" with defined corner tolerance G203 Corner smoothing with defined radius up to maximum tolerance G210 Power control axis selection/Channel 2 G211 Power control pre-selection V1, F1, T1/Channel 2 G212 Power control pre-selection V2, F2, T2/Channel 2 G213 Power control pre-selection V3, F3, T3/Channel 2 G214 Power control pre-selection T4/Channel 2 G215 Power control pre-selection T5/Channel 2 G216 Power control pre-selection T6/pulsing output/Channel 2 G217 Power control pre-selection T7/pulsing output/Channel 2 G220 Angled wheel transformation "off" G221 Angled wheel transformation "on" G222 Angled wheel transformation "on" but angled wheel moves before others G223 Angled wheel transformation "on" but angled wheel moves after others G265 Distance regulation – axis selection G270 Turning finishing cycle G271 Stock removal in turning G272 Stock removal in facing G274 Peck finishing cycle G275 Outer diameter / internal diameter turning cycle G276 Multiple pass threading cycle G310 Power control axes selection /channel 3 G311 Power control pre-selection V1, F1, T1/channel 3 G312 Power control pre-selection V2, F2, T2/channel 3 G313 Power control pre-selection V3, F3, T3/channel 3 G314 Power control pre-selection T4/channel 3 G315 Power control pre-selection T5/channel 3 G316 Power control pre-selection T6/pulsing output/Channel 3 G317 Power control pre-selection T7/pulsing output/Channel 3 Note that some of the above G-codes are not standard. Specific control features, such as laser power control, enable those optional codes. M codes simple definition M00 Unconditional stop M01 Conditional stop M02 End of program M03 Spindle clockwise M04 Spindle counterclockwise M05 Spindle stop M06 Tool change (see Note below) M19 Spindle orientationM20 Start oscillation (configured by G35) M21 End oscillation M30 End of program M40 Automatic spindle gear range selection M41 Spindle gear transmission step 1 M42 Spindle gear transmission step 2 M43 Spindle gear transmission step 3 M44 Spindle gear transmission step 4 M45 Spindle gear transmission step 5 M46 Spindle gear transmission step 6 M70 Spline definition, beginning and end curve 0 M71 Spline definition, beginning tangential, end curve 0 M72 Spline definition, beginning curve 0, end tangential M73 Spline definition, beginning and end tangential M80 Delete rest of distance using probe function, from axis measuring input M81 Drive On application block (resynchronize axis position via PLC signal during the block) M101-M108 Turn off fast output byte bit 1 (to 8) M109 Turn off all (8) bits in the fast output byte M111-M118 Turn on fast output byte bit 1 (to 8) M121-M128 Pulsate (on/off) fast output byte bit 1 (to 8) M140 Distance regulation “on” (configured by G265) M141 Distance regulation “off” M150 Delete rest of distance using probe function, for a probe input (one of 16, M151-M168) M151-M158 Digital input byte 1 bit 1 (to bit 8) is the active probe input M159 PLC cannot define the bit mask for the probe inputs M160 PLC can define the bit mask for the probe inputs (up to 16) M161-M168 Digital input byte 2 bit 1 (to bit 8) is the active probe input M170 Continue the block processing look ahead of the part program (cancel the M171) M171 Stop the block processing look ahead of the probe input part program segment (like a G10) M200 Activate the handwheel operation in the automatic mode (to introduce an offset in the program) M201-M208 Select the axis (by number from 1 to 8) for the handwheel operation M209 Activate the handwheel operation in the automatic mode, with PLC control of the axis selection M210 Deactivate the handwheel input while in the automatic mode M211 Deactivate this handwheel feature and also remove the handwheel offset (if any) M213 Spindle 2 clockwise M214 Spindle 2 counterclockwise M215 Spindle 2 stop M280 Switchable spindle/rotary axis, rotary axis on, first combination M281 Switchable spindle/rotary axis, rotary axis on, second combination M290 Switchable spindle/rotary axis, spindle enabled, first combination M291 Switchable spindle/rotary axis, spindle enabled, second combination Note: Other machine functions, like tool change (usually M06) or coolant control, have their M-code value specified by the PLC application not by the CNC software. Most of the M-code values in above list are configurable.
كلمة سر فك الضغط : books-world.net The Unzip Password : books-world.net أتمنى أن تستفيدوا من محتوى الموضوع وأن ينال إعجابكم رابط من موقع عالم الكتب لتنزيل كتيب يحتوي على شرح معظم أكواد برمجة ماكينات التحكم الرقمي - CNC CNC Programming Codes رابط مباشر لتنزيل كتيب يحتوي على شرح معظم أكواد برمجة ماكينات التحكم الرقمي - CNC CNC Programming Codes
|
|