مقالة بعنوان Drill Presses
منتدى هندسة الإنتاج والتصميم الميكانيكى
بسم الله الرحمن الرحيم

أهلا وسهلاً بك زائرنا الكريم
نتمنى أن تقضوا معنا أفضل الأوقات
وتسعدونا بالأراء والمساهمات
إذا كنت أحد أعضائنا يرجى تسجيل الدخول
أو وإذا كانت هذة زيارتك الأولى للمنتدى فنتشرف بإنضمامك لأسرتنا
وهذا شرح لطريقة التسجيل فى المنتدى بالفيديو :
http://www.eng2010.yoo7.com/t5785-topic
وشرح لطريقة التنزيل من المنتدى بالفيديو:
http://www.eng2010.yoo7.com/t2065-topic
إذا واجهتك مشاكل فى التسجيل أو تفعيل حسابك
وإذا نسيت بيانات الدخول للمنتدى
يرجى مراسلتنا على البريد الإلكترونى التالى :

Deabs2010@yahoo.com


-----------------------------------
-Warning-

This website uses cookies
We inform you that this site uses own, technical and third parties cookies to make sure our web page is user-friendly and to guarantee a high functionality of the webpage.
By continuing to browse this website, you declare to accept the use of cookies.
منتدى هندسة الإنتاج والتصميم الميكانيكى
بسم الله الرحمن الرحيم

أهلا وسهلاً بك زائرنا الكريم
نتمنى أن تقضوا معنا أفضل الأوقات
وتسعدونا بالأراء والمساهمات
إذا كنت أحد أعضائنا يرجى تسجيل الدخول
أو وإذا كانت هذة زيارتك الأولى للمنتدى فنتشرف بإنضمامك لأسرتنا
وهذا شرح لطريقة التسجيل فى المنتدى بالفيديو :
http://www.eng2010.yoo7.com/t5785-topic
وشرح لطريقة التنزيل من المنتدى بالفيديو:
http://www.eng2010.yoo7.com/t2065-topic
إذا واجهتك مشاكل فى التسجيل أو تفعيل حسابك
وإذا نسيت بيانات الدخول للمنتدى
يرجى مراسلتنا على البريد الإلكترونى التالى :

Deabs2010@yahoo.com


-----------------------------------
-Warning-

This website uses cookies
We inform you that this site uses own, technical and third parties cookies to make sure our web page is user-friendly and to guarantee a high functionality of the webpage.
By continuing to browse this website, you declare to accept the use of cookies.



 
الرئيسيةالبوابةالتسجيلدخولحملة فيد واستفيدجروب المنتدى

شاطر
 

 مقالة بعنوان Drill Presses

اذهب الى الأسفل 
كاتب الموضوعرسالة
Admin
مدير المنتدى
مدير المنتدى
Admin

عدد المساهمات : 17748
التقييم : 32050
تاريخ التسجيل : 01/07/2009
الدولة : مصر
العمل : مدير منتدى هندسة الإنتاج والتصميم الميكانيكى

مقالة بعنوان Drill Presses Empty
مُساهمةموضوع: مقالة بعنوان Drill Presses   مقالة بعنوان Drill Presses Emptyالسبت 14 نوفمبر 2020, 9:43 pm

أخوانى فى الله
أحضرت لكم
مقالة بعنوان
Drill Presses

مقالة بعنوان Drill Presses D_p_e_10
و المحتوى كما يلي :

Drilling machines, or drill presses, are primarily used to drill or enlarge a
cylindrical hole in a workpiece or part. The chief operation performed on the drill press is
drilling, but other possible operations include: reaming, countersinking, counterboring,
and tapping.
The floor type drill press used in the Student Shop is a very common machine,
found in both home and industrial workshops. This style drill press is composed of four
major groups of assemblies: the head, table, column, and base.
The head contains the motor and variable speed mechanism used to drive the
spindle. The spindle is housed within the quill, which can be moved up or down by either
manual or automatic feed. The table is mounted on the column, and is used to support the
workpiece. The table may be raised or lowered on the column, depending upon the
machining needs. The column is the backbone of the drill press. The head and base are
clamped to it, and it serves as a guide for the table. The cast-iron base is the supporting
member of the entire structure.Procedures;
Successful operation of the drill press requires the operator to be familiar with the
machine and the desired operation. The following are some good observations to follow
when drilling a hole:
1. Prior to drilling a hole, locate the hole by drawing two crossing lines. Use a center
punch to make an indentation for the drill point to aid the drill in starting the hole.
2. Select the proper drill bit according to the size needed.
3. Select an appropriate size center drill.
4. Select a cutting fluid.
5. Properly secure the workpiece to the table.
6. Select the correct RPM for the drill bit. Take into account: size of bit, material, and
depth of hole to be drilled.
7. Use an interrupted feed, called peck drilling, to break up the chips being produced.
8. Pilot holes should be used on holes larger than 3/8” dia. Holes are to be enlarged in no
more than 1/4” increments.
9. Clean the drill press and surrounding area when finished.
*** Hard and fast rules are not always practical for every operation performed in a
drill press, since many factors can influence the speed and feed at which a material can be
worked. The above suggestions, combined with knowledge of the tool being used, will
provide a reasonable guideline for the operator using a drill press.
Tooling;
Twist drills- A twist drill is a pointed cutting tool used for making cylindrical
holes in the workpiece. It has helical flutes along its length for clearing chips from the
holes. Twist drills are the most common used today, but there are many other styles with
different purposes. A twist drill is composed of three major parts: a shank, body, and
point. The shank is the part of the drill bit held in the spindle of the drill press. The drill
press’ power is transferred through the shank. Shanks are either one of two styles, straight
or tapered. Straight shank drills are held in a friction chuck. Slippage between the drill bit
and the chuck is often a problem, especially for larger drills. When using drill bits larger
than 1/2” dia., tapered shank drill bits are often used. These provide greater torque with
less slippage than straight shank drill bits. The body, as described above, generally has
two flutes to clear chips. These flutes are not cutting edges and should not be used for
side cutting as an end mill. The point of the drill bit does all of the cutting action, which
produces the cut chips. The point is ground on the end of the drill bit.
Holes produced by twist drill bits are generally oversize by as much as up to 1%
of the bit’s dia. The accuracy of the hole is dependent on the following factors: size of the
bit, accuracy of the bit’s point, accuracy of the chuck, accuracy and rigidity of the
spindle, rigidity of the press, and rigidity of the workpiece in its setup. All holes to be
drilled should be started with a centerpunch, centerdrill, or both.Twist Drill Formats;
1. Number sizes: #80 (.0135”) to #1 (.228”)
2. Letter sizes: A (.234”) to Z (.413”)
3. Fractional sizes: 1/64” (.0156”) upwards by 64ths/inch
Reamers- A reamer is a precision cutting tool designed to finish a hole to a
specific dia. Since drill bits produce slightly oversized holes, reamers are used where
precision tolerances are required, .001”. Reamers have little if no cutting action on their
ends, so a pilot hole is required as a preoperation to reaming. Some general guidelines for
using reamers are:
1. The cutting speed for reaming should be about 1/3 of the speed used for drilling
operation of the same material.
2. Before reaming, leave about .010” of material on holes up to 1/2”, and about .020” of
material on larger holes.
3. Never rotate a reamer in the reverse direction.
4. Use the proper cutting fluid for the material.
5. Remove the reamer from the hole occasionally while cutting to clear chips, which can
cause galling on the surface of the precision hole.
6. Never stop the machine with the reamer in the hole.
7. Clean and return the reamer to its proper storage place.
Countersinks- Countersinking is an operation in which a cone-shaped
enlargement is cut at the top of a hole to form a recess below the surface. A conical
cutting tool is used to produce this chamfer. When countersinking, the cutter must be
properly aligned with the existing hole, and should be rotated about 1/3 the cutting speed
of the drilling operation for the hole. Countersinking is useful in removing burrs from
edges of holes, as well as providing a flush fit for flat-headed fasteners.
Counterbores- Counterboring is the process of cylindrically enlarging a hole part
way along its length. A counterbore cutter is similar to a drill bit in that it has a shank and
fluted body, but instead of a point, it has a smaller diameter pilot portion. The pilot fits
into a pre-drilled hole, and guides the counterbore. Therefore the counterbore must be
aligned with the original hole, so the pilot will follow the hole properly. Counterbores are
used to accommodate studs, bolts, or socket head capscrews where a flush surface
application is required.Tapping- A tap is a tool used to cut internal threads in a cylindrical hole. A tap is
fluted like a drill, but the flutes actually perform the cutting operation. The flutes extend
the length of the threaded section and also serve to remove the chips being produced. The
most common taps used are:
1. The starting or tapered tap. This tap is used to start threads. At least the first six threads
of this tap are tapered before the full diameter of the thread is reached.
2. The plug tap. This is the general use tap, and is used to cut threads after the taper tap
has been used and removed. Three to five of its first threads are tapered. This is the last
tap used if the hole extends all the way through the workpiece.
Cutting fluids should always be used when tapping holes. It is also recommended
to advance the tap one full turn and the reverse it 1/4 turn to break the chip being formed.
Always use a tap handle, not pliers or a crescent wrench to turn the tap. They can damage
the tap, and the unequal torque provided can cause a thread to be cut poorly.
Safety;
The drill press can be a safe machine, but only as long as the student is aware of
the hazards involved. Chips are produced in great quantities, and must be safety handled.
The rotating chuck and cutter can also be a hazard. Develop safe working habits in the
use of protective clothes, set-ups, and tools. The following rules must be observed when
working on any drill press in the Student Shop:
1. No attempt should be made to operate a drill press until you are certain you understand
the proper procedures for its use.
2. Dress appropriately. Remove all watches and jewelry. Safety glasses or goggles are a
must.
3. Plan out your work thoroughly before starting.
4. Know the location of the OFF button.
5. Clamp all work securely to the table.
6. Always remove the chuck key immediately after using it. A key left in the chuck will
be thrown out at a high velocity when the machine is turned on. Never let the chuck key
leave your hand except to put it back into its holder.
7. Never stop a drill press spindle with your hand after you have turned off the machine.
Chips often build up around the chuck.
8. Use a brush, not your hands, to remove chips from the machine. Do not clean up while
the machine is running.
9. Remove burrs from drilled workpieces as soon as possible.
10. Keep the floor area clean. Immediately wipe up any oil spills.


 كلمة سر فك الضغط : books-world.net
The Unzip Password : books-world.net
أتمنى أن تستفيدوا من محتوى الموضوع وأن ينال إعجابكم

رابط من موقع عالم الكتب لتنزيل مقالة بعنوان Drill Presses
رابط مباشر لتنزيل مقالة بعنوان Drill Presses
الرجوع الى أعلى الصفحة اذهب الى الأسفل
حفيظ
مهندس تحت الاختبار
مهندس تحت الاختبار
حفيظ

عدد المساهمات : 3
التقييم : 5
تاريخ التسجيل : 17/11/2020
العمر : 37
الدولة : الجزائر
العمل : صناعة
الجامعة : وهران

مقالة بعنوان Drill Presses Empty
مُساهمةموضوع: رد: مقالة بعنوان Drill Presses   مقالة بعنوان Drill Presses Emptyالثلاثاء 17 نوفمبر 2020, 1:42 am

استاذ بارك الله فيك على الموضوع
و احتاج مساعدة بخصوص موضوع الفلكس المكون لغلاف الكترودات اللحام من نوع e6013 و e7018 و النسب لمختلف المكونات (welding flux ,for e6013 and e7018)
مع تشكراتي مسبقا على مجهوداتكم
الرجوع الى أعلى الصفحة اذهب الى الأسفل
Admin
مدير المنتدى
مدير المنتدى
Admin

عدد المساهمات : 17748
التقييم : 32050
تاريخ التسجيل : 01/07/2009
الدولة : مصر
العمل : مدير منتدى هندسة الإنتاج والتصميم الميكانيكى

مقالة بعنوان Drill Presses Empty
مُساهمةموضوع: رد: مقالة بعنوان Drill Presses   مقالة بعنوان Drill Presses Emptyالخميس 26 نوفمبر 2020, 11:55 pm

حفيظ كتب:
استاذ بارك الله فيك على الموضوع
و احتاج مساعدة بخصوص موضوع الفلكس المكون لغلاف الكترودات اللحام من نوع e6013 و e7018 و النسب لمختلف المكونات (welding flux ,for e6013 and e7018)
مع تشكراتي مسبقا على مجهوداتكم


فضلاً قم بعمل طلب هنا بالتفصيل
https://www.eng2010.com/post?f=17
وسيتم الرد عليك فى أقرب وقت إن شاء الله
موضوع يشرح طريقة عمل طلب في منتدى هندسة الإنتاج والتصميم الميكانيكي
https://www.eng2010.com/t190-topic
الرجوع الى أعلى الصفحة اذهب الى الأسفل
 
مقالة بعنوان Drill Presses
الرجوع الى أعلى الصفحة 
صفحة 2 من اصل 1
 مواضيع مماثلة
-
» مقالة مبسطة بعنوان Role of Technical Education
» مقالة بعنوان Reasons for Turning to Slotless Technology
» مقالة بعنوان What Are Dual-motion Hybrid Actuators and Where Do They Excel?
» مقالة بعنوان Why Manufacturers Need to Go Digital Now
» مقالة بعنوان Lifelines for the Smart Factory

صلاحيات هذا المنتدى:لاتستطيع الرد على المواضيع في هذا المنتدى
منتدى هندسة الإنتاج والتصميم الميكانيكى :: المنتديات الهندسية :: منتدى المقالات والمواضيع الهندسية-
انتقل الى: