دورة تعليم المحاكاة باستخدام السوليدوركس - SolidWorks Simulation Training

أخوانى فى الله
أحضرت لكم
دورة تعليم المحاكاة باستخدام السوليدوركس - SolidWorks Simulation Training

و المحتوى كما يلي :

About this course
Prerequisites
Course Design Philosophy
Using this book
A note about files
Conventions used in this book
Class Introductions
Design Validation Products
What is Finite Element Analysis ?
Building the FEA Model
Building the FEA Model - Fixtures
Building the FEA Model - Loads
FEA for structural analysis
Mesh, Nodes, Elements, …
Using Stress Results to Validate Design
Assumptions in Linear, Static Analyses
Check list for SolidWorks Simulation
Lesson 1 The Analysis Process
 Introduction to the Simulation interface
 Perform linear static analysis – Static
study
• Material properties
• Restraints
• Loads
• Mesh
• Run
 Influence of mesh density on displacement
and stress results
 Post-processing
Lesson 2 Mesh Controls, Stress Concentrations and Boundary Conditions
Topics
Using SolidWorks Configurations
Use of mesh controls, automatic transition
FEA Convergence issues
Different boundary conditions
Lesson 3 Assembly Analysis with Contact
Topics
Assembly Analysis Basics
Interference Detection
Global and Local Contact/ Gaps conditions
Lesson 4 Symmetrical and Free Self-Equilibrated Assemblies
Topics
Analyze shrink-fit problem
Use of symmetry
Review stress results in local coordinat systems
Solver options to eliminate rigid body modes
Lesson 5 Assembly Analysis with Connectors
Topics
Connectors
 Rigid
 Spring
 Pin
 Elastic Support
 Bolt
 Spot Weld
 Edge Weld
 Link
 Bearing
Global and local contact conditions
Lesson 6 Compatible/Incompatible Meshing
Topics
Compatible solid element mesh with Bonded contacts
Incompatible solid element mesh with Bonded contacts
Simplified bonding for incompatible solid meshes
Lesson 7 Assembly Analysis Mesh Refinement
Topics
Analyze larger assembly using solid elements
Remote load feature
Define multiple contact conditions
Nontraditional contact and connector use
Analyze mesh quality and question the results of the simulation
Lesson 8 Analysis of Thin Components
Topics
Shell Elements
Mid-plane and surface shell element meshing
Alignment of shell mesh
Evaluating mesh sizes
Evaluating results for shell elements
Reaction forces
Solid vs. Shell meshing
Lesson 9 Mixed Meshing Shells & Solids
Topics
Mixed meshing
Solid-shell bonding
Shell offset
Mesh failure diagnostics
Lesson 10 Mixed Meshing Solids, Beams & Shells
Topics
Beam elements
Joints
Bonding of beams
Post-processing of beam elements
Lesson 11 Design Study
Topics
 Design Study – performing several studies for different
input data (model geometry or loads)
 Stresses in vehicle suspension when vehicle is:
 Stationary and loaded
 Moving at constant acceleration on a smooth road
 Moving on a bumpy road
 Moving at a constant speed on a banking road
 Different loads in different directions
 Review different connectors and fixtures
Lesson 12 Thermal Stress Analysis
Topics
Static analysis with temperature load
Use of various contact conditions
Temperature dependent material properties
Soft spring and Inertia relief options
Lesson 13 Adaptive Meshing
Topics
Why and What is Adaptivity?
What do FEM results depend on?
1. Mesh
2. Type and order of the elements used (Draft or High quality)
3. Other phenomena (numerical errors, modeling errors etc.)
What is our Goal? Is it just to obtain a solution?
Make sure our results are close to some defined accurate solution. (typical parameter is strain
energy density)
How to achieve it?
1. Modify and refine the mesh topology
2. Modify the “order” of elements
Lesson 14 Large Displacement Analysis
Topics
Surface contact
Contact analysis with the large displacement option
Evaluate mesh adequacy for modeling bending stresses
Limitations of the linear material model

كلمة سر فك الضغط : books-world.net
The Unzip Password : books-world.net
أتمنى أن تستفيدوا من محتوى الموضوع وأن ينال إعجابكم
رابط من موقع عالم الكتب لتنزيل دورة تعليم المحاكاة باستخدام السوليدوركس - SolidWorks Simulation Training
رابط مباشر لتنزيل دورة تعليم المحاكاة باستخدام السوليدوركس - SolidWorks Simulation Training

كيفية التسجيل فى منتدى هندسة الإنتاج والتصميم الميكانيكى

طريقة التنزيل من المنتدى خطوة بخطوة

الهارد الشامل والمتكامل لقسم ميكانيكا

******************************************************

دورة تعليم المحاكاة باستخدام السوليدوركس - SolidWorks Simulation Training 761752

» كورس تعليم المحاكاة الغير خطية باستخدام برنامج سوليدوركس - Solidworks Simulation Nonlinear Tutorial Course
» كورس تعليم المحاكاة الاستاتيكية باستخدام برنامج سوليدوركس - Solidworks Simulation Linear Static Assembly Analysis Tutorial Course
» كورس المحاكاة باستخدام برنامج سوليدوركس - SOLIDWORKS Simulation Course
» كورس تعليم المحاكاة باستخدام برنامج فيوجن 360 - Fusion 360 - Simulation Course
» كورس تعليم الريندر على السوليدوركس - Mastering SolidWorks - Rendering and Visualization Training Course