بحث بعنوان A Parametric Study on Lateral Torsional Buckling of European IPN and IPE Cantilevers

أخوانى فى الله
أحضرت لكم بحث بعنوان
A Parametric Study on Lateral Torsional Buckling of European IPN and IPE Cantilevers
H. Ozbasaran

و المحتوى كما يلي :

Abstract—IPN and IPE sections, which are commonly used
European I shapes, are widely used in steel structures as cantilever
beams to support overhangs. A considerable number of studies exist
on calculating lateral torsional buckling load of I sections. However,
most of them provide series solutions or complex closed-form
equations. In this paper, a simple equation is presented to calculate
lateral torsional buckling load of IPN and IPE section cantilever
beams. First, differential equation of lateral torsional buckling is
solved numerically for various loading cases. Then a parametric
study is conducted on results to present an equation for lateral
torsional buckling load of European IPN and IPE beams. Finally,
results obtained by presented equation are compared to differential
equation solutions and finite element model results. ABAQUS
software is utilized to generate finite element models of beams. It is
seen that the results obtained from presented equation coincide with
differential equation solutions and ABAQUS software results. It can
be suggested that presented formula can be safely used to calculate
critical lateral torsional buckling load of European IPN and IPE
section cantilevers.
Keywords—Cantilever, IPN, IPE, lateral torsional buckling
CONCLUSION
In this paper, a parametric equation to calculate LTB load
of cantilever IPN and IPE sections are presented. Section
properties of mentioned sections are simplified and LTB load
parameter is calculated for concentrated load at free end,
uniformly distributed load, combination of concentrated load
at free end and uniformly distributed load and constant
moment cases. However, ./ parameter of presented equation
can be calculated for any loading case. The results obtained by
presented equation, differential equation solutions and
ABAQUS software models are compared. It is seen that
results obtained by presented equation perfectly coincide with
differential equation and ABAQUS solutions. Lateral torsional
buckling loads of IPN and IPE section cantilevers can be
determined by presented formula and can be safely used in
design procedures.

كلمة سر فك الضغط : books-world.net
The Unzip Password : books-world.net
أتمنى أن تستفيدوا من محتوى الموضوع وأن ينال إعجابكم
رابط من موقع عالم الكتب لتنزيل بحث بعنوان A Parametric Study on Lateral Torsional Buckling of European IPN and IPE Cantilevers
رابط مباشر لتنزيل بحث بعنوان A Parametric Study on Lateral Torsional Buckling of European IPN and IPE Cantilevers

كيفية التسجيل فى منتدى هندسة الإنتاج والتصميم الميكانيكى

طريقة التنزيل من المنتدى خطوة بخطوة

الهارد الشامل والمتكامل لقسم ميكانيكا

******************************************************

بحث بعنوان A Parametric Study on Lateral Torsional Buckling of European IPN and IPE Cantilevers 761752

» رسالة ماجستير بعنوان The “45 Degree Rule” and Its Impact on Strength and Stiffness of a Shaft Subjected to a Torsional Load
» بحث بعنوان Effect of Aspect Ratio on Buckling Load for Laminated Composite Decks Plates
» بحث بعنوان Effect of Boundary Conditions on Buckling Load for Laminated Composite Decks Plates
» بحث بعنوان Parametric Design of Delta Robot
» بحث بعنوان Buckling Strength of Adhesively-Bonded Single and Double-Strap Repairs on Carbon-Epoxy Structures