Admin مدير المنتدى
عدد المساهمات : 18961 التقييم : 35389 تاريخ التسجيل : 01/07/2009 الدولة : مصر العمل : مدير منتدى هندسة الإنتاج والتصميم الميكانيكى
| موضوع: بحث بعنوان Variable-stiffness composite panels - Defect tolerance under in-plane tensile loading الإثنين 14 ديسمبر 2020, 1:17 am | |
|
أخوانى فى الله أحضرت لكم بحث بعنوان Variable-stiffness composite panels: Defect tolerance under in-plane tensile loading O. Falcó a, J.A. Mayugo a, C.S. Lopes b, N. Gascons a, J. Costa
و المحتوى كما يلي :
Abstract Automated Fiber Placement is being extensively used in the production of major composite components for the aircraft industry. This technology enables the production of tow-steered panels, which have been proven to greatly improve the structural efficiency of composites by means of in-plane stiffness variation and load redistribution. However, traditional straight-fiber architectures are still preferred. One of the reasons behind this is related to the uncertainties, as a result of process-induced defects, in the mechanical performance of the laminates. This experimental work investigates the effect of the fiber angle discontinuities between different tow courses in a ply on the un-notched and open-hole tensile strength of the laminate. The influence of several manufacturing parameters are studied in detail. The results reveal that ‘ply staggering’ and ‘0% gap coverage’ is an effective combination in reducing the influence of defects in these laminates. Conclusions In the present experimental work, the effect of the fiber angle discontinuities between different tow courses in a ply on the unnotched and open-hole laminates tensile strength was investigated. The influence of the percentage of coverage and the staggering technique were studied in detail. Test specimens were designed and manufactured to represent a sub-domain of a VSP containing a worst-case tow-angle discontinuity, and different practical manufacturing strategies to tackle such discontinuity: (i) tow-dropping with 0% gap coverage (gaps); (ii) tow-dropping with 100% gap coverage (overlaps); and (iii) towdropping with 0% gap coverage and ply staggering. After a geometrical observation of overlapping and gap defects produced by the tow-drop manufacturing method, test specimens were loaded until failure. In comparison with the baseline specimens representing straight-fiber panels without defects, the configuration with 0% gap coverage and no staggering presents the most critical strength reduction; as a results of the clustering of gaps. When the ply staggering technique is applied, these effects are highly mitigated. Therefore, ‘ply staggering’ and ‘0% gap coverage’ would be expected to be an effective combination to lessen the influence of defects in VSP. The experimental results show that the stress concentration, induced by the presence of the hole in OHT specimens, has a higher influence on failure than that induced by the presence of manufacturing defects in un-notched specimens. Additionally, the analysis Fig. 12. (a) Comparison of load-crosshead displacement for different open-hole laminate configurations. (b) Delamination and damage on tested specimen. (For interpretation of the references to colour in this figure legend, the reader is referred to the web version of this article.) 30 O. Falcó et al. / Composites: Part A 63 (2014) 21–31of failure mechanisms in un-notched specimens reveals that large delaminations initiate in the vicinity of the tow-drop defects, which are then followed by extensive matrix cracking and finally fiber failure. This is probably caused by the amplification of the interlaminar stresses around the defects. Acknowledgements The authors acknowledge the financial support of the Ministerio de Economía y Competitividad of Spain under Project MAT2009-07918. The first author would also like to thank Generalitat de Catalunya for the FI predoctorate Grant 2010FI_B00658
كلمة سر فك الضغط : books-world.net The Unzip Password : books-world.net أتمنى أن تستفيدوا من محتوى الموضوع وأن ينال إعجابكم رابط من موقع عالم الكتب لتنزيل بحث بعنوان Variable-stiffness composite panels - Defect tolerance under in-plane tensile loading رابط مباشر لتنزيل بحث بعنوان Variable-stiffness composite panels - Defect tolerance under in-plane tensile loading
|
|