Admin
مدير المنتدى
عدد المساهمات : 18745
التقييم : 34763
تاريخ التسجيل : 01/07/2009
الدولة : مصر
العمل : مدير منتدى هندسة الإنتاج والتصميم الميكانيكى
 |  موضوع: مقالة بعنوان Centrifugal Pumps - Using Vibration Analysis to Detect Problems الجمعة 14 أكتوبر 2022, 2:14 am | |
| 
أخواني في الله
أحضرت لكم
مقالة بعنوان
Centrifugal Pumps - Using Vibration Analysis to Detect Problems
www.technicalassociates.net
و المحتوى كما يلي :
PRINCIPLES OF OPERATION:
Centrifugal pumps are among the more versatile and widely used pieces of rotating mechanical
equipment found today. Pumps are essential in almost all utilities services and power generation
plants. It is estimated that pumps consume approximately 31% of rotating equipment electrical
power used throughout industry. Pumps are a vital part of our lives on the planet today.
The basic principal of operation for a centrifugal pump is that a shaft mounted rotating impeller
inside a housing (volute) imparts energy to the fluid being moved. Centrifugal pumps utilize
centrifugal force (thus their name) to increase the velocity of the fluid as it passes through the
impeller and exits at the tip or periphery of the impeller. This action converts mechanical energy
(shaft torque) into kinetic energy by acceleration of the fluid to a higher velocity and pressure
(potential energy).
PUMP PERFORMANCE:
Pumps follow basic laws of performance. These are useful in determining the effect of changes to
the operating parameters and can help determine the cause of operational problems. These basic
laws apply to most centrifugal pumps or pump systems.
1. Fluid flow (quantity) varies directly with the impeller rotating speed or diameter change.
2. Head generated (feet of head) varies with the square of the impeller tip speed (ft/sec)2
divided by 64.4 (2g, ft/sec2).
3. Horsepower varies directly with the volume and specific gravity of the fluid pumped.
4. Horsepower varies with the cube of a change in rotating speed or impeller diameter.
DETECTING PUMP PROBLEMS USING VIBRATION ANALYSIS:
Centrifugal pumps are subjected to operational forces generated by their operating speed, system
head, pressure and piping arrangement. These operational forces cause forced vibration and may
originate from the rotating parts or operating conditions (flow quantity, pressures, speed and
arrangement). This vibration reduces the expected life of the pump bearings and other
components.
SUMMARY OF COMMON PUMP VIBRATION PROBLEMS:
(Detected Using Vibration Analysis)
1. Cavitation:
Cavitation typically generates random, higher frequency broadband energy, which is
sometimes superimposed with blade pass frequency harmonics (multiples). Cavitation is a
symptom of insufficient net positive suction head (NPSH). Cavitation results when the
absolute pressure of the liquid at the pump impeller inlet approaches the vapor pressure of
the liquid causing vapor pockets to form and collapse (implode) as they pass through the
pump impeller. The collapsing of the vapor bubbles can be very destructive and mayCENTRIFUGAL PUMPS
USING VIBRATION ANALYSIS TO DETECT PROBLEMS
 Copyright 2014 Technical Associates of Charlotte, P.C. Page 2
www.technicalassociates.net
damage the pump and impeller. When present, cavitation often sounds as if “marbles” or
“gravel” are passing through the pump. The positive suction head required to correct
suction cavitation is known as “NPSHR” (Net Positive Suction Head Required). This value
is typically supplied by the pump manufacturer.
2. Pump Flow Pulsation:
Pump flow pulsation is a condition that develops when a pump is operating near its shut-off
head. The vibration in the time waveform will be sinusoidal. In addition, the spectra will still
be dominated by 1X RPM and blade pass frequency. However, these peaks will be
unstable, increasing and decreasing as the flow pulsation occurs. Pressure gauges on the
discharge piping will fluctuate up and down. If the pump has a discharge swing check
valve, the valve arm and counter-weight will bounce back and forth indicating unstable flow.
3. Bent Pump Shaft:
Bent shaft problems cause high axial vibration with axial phase differences tending towards
180° on the same rotor. Dominant vibration normally occurs at 1X RPM if bent near shaft
center, but at 2X RPM if bent near the coupling. Pump bent shafts are more common at or
near the coupling. Dial indicators can be used to confirm a bent shaft.
4. Unbalance of Pump Impeller:
Pump impellers should be precision balanced at the pump original equipment manufacturer
(OEM). This is particularly important since forces due to unbalance greatly affect life of the
pump bearings (bearing life varies inversely with the cube of imposed dynamic load). The
pump may have a center-hung or an overhung impeller. If the impeller is center-hung, force
unbalance often predominates over couple unbalance. In this case, highest vibration will
typically be in the radial (horizontal and vertical) direction. The highest amplitude will be at
the pump operating speed (1X RPM). In this case of force unbalance, the horizontal
outboard and inboard phase will be about the same (+/- 30°), as will the vertical phase. In
addition, there is usually about a 90° difference in horizontal and vertical phase on each
pump bearing (+/- 30°). Center-hung impellers, by their design, have balanced axial forces
on the inboard and outboard bearings. Elevated axial vibration is a strong indication of
pump impeller obstruction by foreign objects causing the axial vibration typically at running
speed to increase.
If the pump has an overhung impeller, this will usually cause high 1X RPM in both the axial
and radial directions. Axial readings tend to be in-phase and steady, whereas radial phase
readings might be unsteady. Overhung rotors have both force and couple unbalance, each
of which will likely require correction. Thus, correction weights will most always have to be
placed in 2 planes to counteract both force and couple unbalance. In such cases, it will
most always be necessary to remove the pump rotor and place it on a balance machine to
balance it to sufficient precision since 2 planes will not normally be accessible in the field.
5. Shaft Misalignment:
Shaft misalignment is a condition found on direct drive pumps where the centerlines of two
coupled shafts are not coincident. Parallel misalignment is a condition where the shaft
centerlines are parallel but offset from one another. The vibration spectrum often will show
2X higher than 1X and a 3X higher than normal with 180° out of phase across the couplingCENTRIFUGAL PUMPS
USING VIBRATION ANALYSIS TO DETECT PROBLEMS
Copyright 2014 Technical Associates of Charlotte, P.C. Page 3
www.technicalassociates.net
in the radial direction. Angular misalignment will show high axial 1X with some 2X and 3X
and a 180° phase shift axially across the coupling.
6. Pump Bearing Problems:
Peaks (with harmonics) at nonsynchronous frequencies is a symptom of rolling element
bearing wear. Short bearing life for pumps is typically the result of poor bearing selection
for the application, such as excessive loads, poor lubrication or high temperatures. If the
model number and manufacturer of the bearings are known, then the specific fault
frequencies for the outer race, inner race, rolling elements and cage can be determined.
These fault frequencies for such bearings are found within tables of most predictive
maintenance (PdM) software today.
Centrifugal pumps have unique problems due to the operational conditions to which they are
subjected that are not common to other machine types. These problems (or faulty conditions) can
then generate some unique vibration spectra and time waveforms as outlined above. This article is
intended to be a summary of common pump problems that vibration analysis can detect and
identify. If reliability technicians obtain the proper vibration training they need that instructs them
how to identify such problems and faulty operating conditions, they can utilize vibration analysis to
identify each of the aforementioned problems (and other faults) before they result in failure. In turn,
this will provide considerable savings in maintenance and operations expenditures if such
problems are detected during early stages preventing catastrophic failure and causing loss of
production and downtime. Studies have shown that centrifugal pumps are some of the most
common machine types in use throughout virtually all industry types. The key to detecting and
resolving such problems on centrifugal pumps is obtaining vibration analysis training from
instructors who themselves have considerable vibration expertise, specifically with these particular
machines. Technical Associates is one of several organizations offering vibration training on
centrifugal pumps. Not only do they provide instruction on how to detect such faults using vibration
signature analysis, but also how to apply time waveform analysis on these unique machine types.
In addition, most training service providers offer vibration analysis certification through a written
examination as confirmation of the student’s comprehension of the course material and the basics
for detecting common pump problems using vibration analysis.
كلمة سر فك الضغط : books-world.net
The Unzip Password : books-world.net
أتمنى أن تستفيدوا من محتوى الموضوع وأن ينال إعجابكم
رابط من موقع عالم الكتب لتنزيل مقالة بعنوان Centrifugal Pumps - Using Vibration Analysis to Detect Problems
رابط مباشر لتنزيل مقالة بعنوان Centrifugal Pumps - Using Vibration Analysis to Detect Problems 
|
|
